thick casting
英 [θɪk ˈkɑːstɪŋ]
美 [θɪk ˈkæstɪŋ]
【化】厚壁铸件
双语例句
- The X-way allow a workman in a factory to look into a thick steel casting.
光可以使铸造车间的工人看到厚的铸钢件的内部。 - Production of thick section and high strength casting using low alloy cast iron
利用低合金铸铁生产厚壁高强度铸件的研究 - Study on Simulation of Level Fluctuation in Wide and Thick Slab Continuous Casting Mould with Argon Blowing
吹氩宽厚板坯连铸结晶器内液面波动行为的水模型研究 - Water Modeling Study on Optimization of Fluid Control Devices in a Wide and Thick Slab Continuous Casting Tundish
宽厚板坯连铸中间包内控流结构优化水模实验研究 - The successful experience of thick steel plates to replace casting of hydraulic turbine runner lower ring
水轮机转轮下环由厚钢板卷焊替代铸件的成功经验 - Research on the Repair Welding of Thick Casting
关于厚大铸铁件补焊工艺的研究 - The r value of sample is difference about 0.01~ 0.09 between thin slab casting and thick slab casting.
采用连铸薄板坯轧制的试件r值与常规厚板坯相比相差0.02~0.04。 - Application of Proportional Solidification to Thick Plate Type Gray Casting
厚实平板类灰铁件的均衡凝固工艺 - Thick-walled Cast Pipe with Small Caliber in Centrifugal Casting
小口径厚壁铸管的离心铸造 - A YSZ film of about 12 μ m thick was deposited on the anode by centrifugal casting, and SEM result showed that the film was well adhered to the anode.
在NiO-YSZ阳极上用离心沉积方法制备了一层厚12μmYSZ薄膜，扫描电子显微镜测试结果表明阳极和电解质薄膜之间的接触良好。 - Welding of the Big-diameter Thick Casting Steel Pipe
大口径厚壁铸钢管焊接 - The influence of operating condition on Gel tape casting process is studied. The bilayers exhibit superior ME coupling compared to thick film composites prepared by tape casting process.
讨论了工艺条件对成型的影响。相较于涂敷膜（tapecasting）复合样品，该双层膜显示出更为优良的ME耦合效应。 - The electric current treatment changes the morphology of primary iron-rich phase from thick plate-like to flower-like and to needle point-like in Al-Fe casting alloys with the increase of electric current density;
对熔体进行电流处理，随电流密度的增大，初生Al3Fe相形貌逐渐由针状转变为花朵状、小针状和针点状； - The technique of centrifugal casting was used. Coating for Centrifugal Casting Pipe The High Purity Aluminium Tube with Large Diameter Spun with Thick Centrifugal Casting Blank
采用厚壁离心铸坯旋压成形大直径高纯铝筒工艺研究 - Research on a method of crack prediction in thick and large casting
厚大铸件热裂纹预测方法研究 - It is found that the treatment by electric current or thermal rate changes the morphology of primary iron-rich phase from thick plate-like to flower-like and needle point-like in casting hypereutectic Al-Fe alloys, as a result, the mechanical property of the alloy is correspondingly improved.
经电流处理或热速处理后的过共晶铝铁合金组织中初生富铁相得到细化，由粗大的板块状变为花朵状和针点状。由于组织得到细化，力学性能也得到了相应提高。 - It is considered that medium thick slab or sheet billet should be adopted for various users 'demands in continuous casting and continuous rolling of hot strip in VAI. It is introduced the characteristic of above technology and production line configuration in VAI.
VAI公司的热带钢连铸连轧基于不同考虑分别主张采用中厚板坯或者薄板坯，文中介绍了VAI的技术思想的特点和热带钢连铸连轧生产线配置方案。 - A silicon based lead zirconate titanate ( PZT) thick film technology by tape casting is studied in this paper.
研究了基于流延技术制备硅基锆钛酸铅（PZT）厚膜的工艺。 - The Research on Producing Thick Section Wall Nodular Iron Casting Using Externally Cooling Technique
采用外冷却生产厚大断面球铁铸件的试验研究